BuildersCount

Weight of Asphalt Calculator

A cubic yard of rolled asphalt weighs about 1.98 tons. Type an amount, or measure the area you will pave.

By BuildersCount · Last checked 4 Oct 2026 · Our sources

Type an amount

Which asphalt?
It is in

Your answer

That is about
1.98tons

1 cubic yard of rolled asphalt.

Volume

  • Cubic yards1
  • Cubic feet27

Weight

  • lb3,960

This answer is a guide. Ask the plant for its own mix weight before you order.

Save or share

Quick answers

Tons of asphalt in a cubic yard
About 1.98 tons once laid and rolled. Spread out before rolling, a yard holds about 1.58 tons.
Yards of asphalt in a ton
About 0.51 cubic yards once rolled, or 0.63 before rolling.
Weight per square yard
110 lb for each inch of thickness, rolled. So 2 in thick is 220 lb a square yard.
Weight of asphalt per cubic foot
About 147 lb, rolled.
Tons of asphalt in a dump truck
A tri-axle truck carries about 22 tons, says a New York asphalt maker. A tandem carries about 12–18 tons of stone or soil.

How to work it out

  1. Measure the length and width in feet. Multiply them, then divide by 9 for square yards.
  2. Multiply by the thickness in inches, after rolling.
  3. Multiply by 110 lb, then divide by 2,000 for tons. That is the whole formula.
  4. Got cubic yards? Multiply them by 1.98 for tons of rolled asphalt.

100 square yards, 2 in thick
100 × 2 × 110 = 22,000 lb
22,000 ÷ 2,000 = 11 tons

Asphalt weight: rolled, loose and millings

The Asphalt Institute gives 110 lb per square yard for each inch of rolled asphalt. That works out to 1.98 tons a cubic yard.

Hot asphalt gets thinner as it is rolled. For dense mixes, the Institute says to spread it 1.25 times as thick as the finished layer. Open mixes need less. So unrolled asphalt takes more room for the same tons.

What 1 cubic yard of asphalt weighs
AsphaltPoundsTonsPounds per cubic footCubic yards in 1 ton
Laid and rolled3,9601.981470.51
Spread, before rolling3,1681.581170.63
Millings, loose2,6501.33980.75

Rolled and before rolling are worked out from the Asphalt Institute’s rules. Millings are from Ohio DOT.

Millings are old asphalt, crushed for reuse. They are also sold as crushed or recycled asphalt.

The weight of one cubic foot is the specific weight of asphalt. In metric, rolled asphalt is about 2,350 kg a cubic meter, or 2.35 tonnes.

Square yards to tons of asphalt

Paving is measured in square yards (sy) and inches thick. A square yard is 9 sq ft.

Asphalt by the square yard, after rolling
ThicknessPounds per square yardTons per 100 square yardsSquare yards per tonSquare feet per ton
1.5 in1658.312.1109
2 in220119.182
2.5 in27513.87.365
3.5 in38519.35.247

At 110 lb per square yard per inch. No extra for edges.

For a new driveway, Colorado’s asphalt group uses a 2 in bottom layer and a 1.5 in top layer. Oregon’s design guide lays a driveway in one 2.5 in layer.

A driveway carries heavy loads. Check your local building rules, or ask a builder or engineer.

Asphalt conversion: cubic yards to tons

Multiply cubic yards by the tons in one yard. Make sure you know if the yards are rolled or not yet rolled.

Tons in cubic yards of asphalt
AmountRolledBefore rollingMillings
1 cubic yard1.981.581.33
2 cubic yards3.963.172.65
5 cubic yards9.97.926.63
10 cubic yards19.815.8413.25
20 cubic yards39.631.6826.5

Hot mix rolled, or spread before rolling. Millings are loose in the truck.

How much asphalt is in a truckload?

Plants sell hot mix by the ton. Gernatt, a New York asphalt maker, says its tri-axle truck carries about 22 tons. Two Pennsylvania yards give 22–23 tons for their tri-axles.

Tons per load, and truckload coverage at 2 in thick
TruckTonsSquare yards covered
Tandem dump truck12–18109–164
Tri-axle dump truck22200
Tractor-trailer dump35318

Tandem tons are for stone and soil loads, from 3 sellers. We found no asphalt figure for a tandem.

Gernatt says its 35 ton tractor-trailer is not meant for home delivery. It needs a large, flat place to dump.

A truck of heavy material reaches its weight limit before its box is full. On the Interstate, a loaded truck may weigh up to 80,000 lb in all, says the FHWA.

We found no seller’s cost for a full load, so ask your plant. Our asphalt calculator has a price per ton.

Questions people ask

How much does a yard of asphalt weigh?

About 3,960 lb, or 1.98 tons, once laid and rolled. Spread out before rolling, a yard weighs about 3,168 lb.

How do you convert cubic yards to tons of asphalt?

Multiply the cubic yards by 1.98 for rolled asphalt. So 5 cubic yards is about 9.9 tons.

How do you convert square yards to tons of asphalt?

Multiply square yards × inches thick × 110, then divide by 2,000. 100 square yards at 2 in is 11 tons.

How do you convert square feet to tons of asphalt?

Divide the square feet by 9 to get square yards. Then multiply by the inches and 110, and divide by 2,000.

How much is a load of asphalt?

About 22 tons in a tri-axle truck. At 2 in thick, that covers about 200 square yards.

How much does a ton of asphalt weigh?

2,000 lb, as a US ton is 2,000 lb. That is about 0.51 cubic yards of rolled asphalt.

How much does recycled asphalt weigh?

Ohio DOT puts asphalt millings at 2,650 lb a cubic yard, loose in the truck. So a ton is about 0.75 cubic yards.

Where our numbers come from

Made by BuildersCount. Last checked 4 Oct 2026.

Cite this page

BuildersCount. (2026, October 4). Weight of Asphalt Calculator. https://builderscount.com/asphalt-weight/